CONTENTS
=============================
1. System Requirements
2. Supported Personal Information Managers (PIMS)
3. Install/Uninstall
4. USB Driver Software
4.1 DCU-11
4.2 DSS-20
4.3 DSS-25
4.4 USB cable
5. Configuration
5.1 Sync Settings
5.2 How to connect Sony Ericsson mobile phones for PC connect over Bluetooth
5.3 How to connect Sony Ericsson mobile phones for PC connect over Serial cable
6. How to install Sony Ericsson mobile phone modems
6.1 Install Sony Ericsson mobile phone Bluetooth modem
6.2.1 Install Sony Ericsson mobile phone real USB modem
6.2.2 Install Sony Ericsson mobile phone DCU-11, DSS-20 and DSS-25 USB modem
6.2.3 Install Sony Ericsson mobile phone serial modem
6.3.1 Install Sony Ericsson mobile phone IrDA modem for Windows 2000
6.3.2 Install Sony Ericsson mobile phone IrDA modem for Windows XP service pack 1A
6.3.3 Install Sony Ericsson mobile phone IrDA modem for Windows XP service pack 2
7. Limitations
8. Known Issues February 10, 2006

=====================================================================
1. SYSTEM REQUIREMENTS
=====================================================================
The Sony Ericsson PC Suite is designed to work with
Windows 2000 Professional SP3 or SP4, Windows XP Home SP1 and SP2, Windows XP Pro SP1 and SP2.

The general system requirements are:

At least 400 MB free hard disk space.
Internet Explorer 5.0 or later has to be installed.

Windows 2000 with SP3 or SP4: 64 MB RAM, 266 MHz
Windows XP Home with SP1 or SP2: 128 MB RAM, 300 MHz
Windows XP Pro with SP1 or SP2: 128 MB RAM, 300 MHz

The Operating Systems Windows 2000, Windows XP Home and
Windows XP Pro will allow Installation while older Operating Systems,
e.g. Windows 98, Windows ME and Windows NT are blocked.

It is recommended that the PC SW is installed in the same language as
the Operating System otherwise trash characters in the applications
might be the result, especially for Asian languages.

=====================================================================
2. SUPPORTED PERSONAL INFORMATION MANAGERS (PIMS)
=====================================================================
The Sony Ericsson PC Suite is designed to work with the following PIMs:

Windows Address Book
Outlook 2000 SR-1 or higher
Outlook 2002
Outlook 2003
Lotus Notes 5
Lotus Notes 6
Lotus Notes 6.5

=====================================================================
3. INSTALL/UNINSTALL
=====================================================================
It is recommended that all Windows applications have been closed
before the installation is started.

To repair a faulty installation launch the installation application
from the CD or the web package. Choose "Repair" in the next dialog.
The original CD or web package is required to complete the repair.
You can also perform a repair from Add/Remove programs in Control panel.
It is recommended to restart the computer before you do the repair.

To uninstall the software launch the installation application from
the CD or the web package. Choose "Remove" in the next dialog.
The original CD or the web package is required to complete the uninstallation.
You can also perform an uninstallation from Add/Remove programs in Control panel.
It is recommended to restart the computer before you do the uninstallation.

To modify the installation launch the installation application from
the CD or the web package. Choose "Modify" in the next dialog.
The original CD or the web package is required to complete the modification.
You can also perform a modification from Add/Remove programs in Control panel.

If doing an installation over an earlier version of the PC Suite and a phone
used together with the earlier PC Suite can not be found, please uninstall
the phone driver and install it again.

Pressing SHIFT when the CD is inserted will temporarily disable the
Autorun function.

For updates visit www.sonyericsson.com

=====================================================================
4. USB DRIVER SOFTWARE
=====================================================================
The CD contains driver software for DCU-11, DSS-20, DSS-25 and USB cable.

When the cable and phone are connected to the computer the Hardware
Wizard will start. Follow the wizard and give the path to the drivers.

=====================================================================
4.1 DCU-11
=====================================================================
The driver software for DCU-11 is located in:
\Drivers\DCU-11

The PC Software has a default configuration to use this these cables.

=====================================================================
4.2 DSS-20
=====================================================================
The driver software for DSS-20 is located in:
\Drivers\DSS-20

The PC Software has a default configuration to use this these cables.

=====================================================================
4.3 DSS-25
=====================================================================
The driver software for DSS-25 is located in:
\Drivers\DSS-25

The PC Software has a default configuration to use this these cables.

=====================================================================
4.4 USB
=====================================================================
The driver software for USB is located in:
\Drivers\USB Cable\

The PC Software has a default configuration to use this USB cable.

=====================================================================
5. CONFIGURATION
=====================================================================

=====================================================================
5.1 SYNC SETTINGS
=====================================================================
Before the first synchronisation, you have to configure the sync
settings. You can choose which data types to sync: Contacts,
Calendar, Tasks and Notes.

It is only possible to change "Sync Manager Settings" while the phone
is connected. If you try to change settings without the phone
connected, then "Sync Manager" will be greyed out.

Field matching between Personal Information Managers (PIM) and phone
Several PIMs are supported on the computer.
We will use Microsoft Outlook 2003 as an example when
describing field matching between PIM and phone. The phone can only
support a limited amount of information, and in the list below we show
which fields that are supported. There is also a limitation on field
lengths in the phone, therefore long field names will be truncated
when displayed in the phone.

PIM (Outlook 2003) Phone

* Data type: Contacts
First name: Name: (All characters up to
Last name: first space is taken
as first name in phone)
Job title: Title:
Company: Company:
E-mail: E-mail:
Web page address: Web address:
Home phone: Home number:
Business phone: Work number:
Mobile phone: Mobile number:
Business fax: Fax number:
Other: Other number:
Business Street: Business Street:
Business City: Business City:
Business State/Province: Business State:
Business ZIP/Postal code: Business Zip code:
Business Country/Region: Business Country:
Home Street: Home Street:
Home City: Home City:
Home State/Province: Home State:
Home ZIP/Postal code: Home ZIP/Postal code:
Home Country/Region: Home Country/Region:
Description field: Info:

* Data type: Calendar
Subject: Subject:
Location: Location:
Start date & time: Start date & time:
End date & time: End date & time:
Reminder: Reminder:
Recurrence: Recurrent appointment:
Description field: Description:

* Data type: Tasks
Subject: Subject:
Due date: Due date:
Status: Status: (limited support
in phone)
Priority: Priority:
Reminder: Reminder:
Description field: Description:

* Data type: Notes
Note: Note:

============================================================================
5.2 HOW TO CONNECT SONY ERICSSON MOBILE PHONES FOR PC CONNECT OVER BLUETOOTH
============================================================================
Preconditions: Windows 2000 SP3 or SP4, Windows XP Home or Pro SP1 or SP2.
Sony Ericsson PC Suite installed.

Step 1:
For external Bluetooth equipment, make sure that the equipment is installed
and connect the external Bluetooth equipment to the PC (please check
your PC and/or Bluetooth equipment manuals for details).

Activate Bluetooth communication on the phone (please check the phone manual
for details).

Start the Bluetooth handling application on your PC (different for different
vendors, please check your PC and/or Bluetooth equipment manuals for details).

Step 2:
Search for available Bluetooth devices within range.

Step 3:
Choose your phone among the devices found.

---------------------------------------------
Note! Steps 4 and 5 can be in reversed order
---------------------------------------------
Step 4:
Enter a passkey in PC (any key) when asked for it. Answer "Yes" to
the "Add to my devices" - question in phone.

Step 5:
Enter the same passkey in phone when asked for it. Device should now be connected
to the PC software.

-----------------------------------------------------------------------------------
Note! if you don't use Windows XP's built-in Bluetooth stack or don't have Widcomms
Bluetooth stack version 1.4.2.10 or later, you need to perform some additional steps.
These steps are described below.
-----------------------------------------------------------------------------------
Step 6:
Search for available services for your phone (please check your PC and/or
Bluetooth equipment manuals for details).

Step 7:
Choose "Serial Port" connection and then select Connect.

Step 8:
Information is given about what COM port the serial port connection will use,
remember the COM port number.
How to find information about the COM port differs between different Bluetooth equipment,
please check your PC and/or Bluetooth equipment manuals for details.

Step 9:
Go to the Start menu/Settings/Control Panel/Phone Monitor Options/COM ports.

Step 10:
Mark the COM port you want to use (See Step 8), and set it to "enabled".

Step 11:
Press Apply and OK. Device should now be connected to the PC software.

===============================================================================
5.3 HOW TO CONNECT SONY ERICSSON MOBILE PHONES FOR PC CONNECT OVER SERIAL CABLE
===============================================================================
Preconditions: Windows 2000 sp3 or higher, Windows XPHome or Windows XPPro.
Sony Ericsson PC Suite installed.

Step 1:
Connect your serial cable to one of your PC's physical COM ports and
then connect your Sony Ericsson mobile phone to the other end of the
serial cable. Remember which COM port you attached the Serial cable to (in most
cases it is COM 1 or COM 2)

Step 2:
Go to Start menu/Settings/Control Panel/Phone Monitor Options/COM ports.

Step 3:
Mark the COM port you want to use (See Step 1), and set it to "enabled".

Step 4:
Press Apply and OK. Device should now be connected
to the PC software.

=====================================================================
6 HOW TO INSTALL SONY ERICSSON MOBILE PHONE MODEMS
=====================================================================
This chapter will describe how to install different Sony Ericsson
mobile phone modems.
If you like to use your Sony Ericsson Mobile Phone as a modem it is
recommended that you install Sony Ericsson Bluetooth Modem.

=====================================================================
6.1 INSTALL SONY ERICSSON MOBILE PHONE BLUETOOTH MODEM
=====================================================================
Step 1:
If not already done, follow Steps 1-5 in Chapter 5.2 to connect the
mobile phone for PC connect over Bluetooth.

Step 2:
Search for available services for your phone (please check your PC
and/or Bluetooth equipment manuals for details).

Step 3:
Choose "Dial-up Networking" and then select Connect.

Step 4:
If a Connect dialog is displayed, click Cancel.

Step 5:
Go to Start menu/Settings/Control Panel and then double click on
"Phone and Modem Options"

Step 6:
Click the Modem tab.
Remember the COM port number used by the Bluetooth Modem.

Step 7:
Click Add...

Step 8:
Tick the "Don't detect my modem; I will select it from a list"
checkbox and click Next.

Step 9:
Select Manufacturer Sony Ericsson Mobile Communications and
then select the Sony Ericsson Bluetooth Modem that matches the
mobile phone model you wish to use. Click next.

Step 10:
Select the same COM port used by the Bluetooth Modem (See Step 6) and
then click Next. (The result will be that you have two Modems attached
to the same COM port. This is OK)

Step 11:
Follow the modem wizard to the end.

Step 12:
Click OK on the Phone and Modem Options dialog. Your modem should
now be successfully installed.

=====================================================================
6.2.1 INSTALL SONY ERICSSON MOBILE PHONES REAL USB MODEM
=====================================================================

When using Real USB, the USB modem installation is bundled within the
actual USB driver installation. This means that no additional modem
installation is necessary.

=============================================================================
6.2.2 INSTALL SONY ERICSSON MOBILE PHONES DCU-11, DSS-20 and DSS-25 USB MODEM
=============================================================================
You have to know which COM port is used for the USB modem. To do this, follow
these steps.

Step 1:
Install the USB cable by following Windows "Found new Hardware wizard" and
provide the appropriate drivers required.

Step 2:
Go to Start menu/Settings/Control Panel/System. Click the "Hardware tab".

Step 3:
Click the "Device Manager" button.

Step 4:
In the Device Manager list, expand the "Ports(COM & LPT)" category.

Step 5:
In the expanded "Ports(COM & LPT)" list, you should find an entry similar to
this one: "SEMC (COM X).
E.g. if you've installed a DSS-25 the entry might look like this:
"SEMC DSS SyncStation (COM8)".
Remember what COM port number is stated within the parenthesis,
because this is the number we're going to install the USB modem on.
----------------------------------------------------------------------
Once we have determined which COM port to use, it is time to proceed
with the actual USB modem installation. This is done in the subsequent
steps below.
----------------------------------------------------------------------
Step 6:
Go to Go to Start menu/Settings/Control Panel and then double click on
"Phone and Modem Options"

Step 7:
Click the Modem tab.

Step 8:
Click Add...

Step 9:
Tick the Don't detect my modem; I will select it from a list
checkbox and click Next.

Step 10:
Select Manufacturer Sony Ericsson Mobile Communications and
then select the Sony Ericsson Serial Modem that matches the
mobile phone model you wish to use. Click next.

Step 11:
Select the COM port used for the Serial modem (See step 5)
and then click Next.

Step 12:
Follow the modem wizard to the end.

Step 13:
Click OK on the Phone and Modem Options dialog. Your modem should
now be successfully installed.

=======================================================================
6.2.3 INSTALL SONY ERICSSON MOBILE PHONES SERIAL MODEM
=======================================================================
Step 1:
Connect your serial cable to one of your PC's physical COM ports and
then connect your Sony Ericsson mobile phone to the other end of the
serial cable. Remember which COM port you attached the Serial cable to
(in most cases it is COM 1 or COM 2)

Step 2:
Go to Go to Start menu/Settings/Control Panel and then double click on
"Phone and Modem Options"

Step 3:
Click the Modem tab.

Step 4:
Click Add...

Step 5:
Tick the Don't detect my modem; I will select it from a list
checkbox and click Next.

Step 6:
Select Manufacturer Sony Ericsson Mobile Communications and
then select the Sony Ericsson Serial Modem that matches the
mobile phone model you wish to use. Click next.

Step 7:
Select the COM port (See step 1) used for the Serial
modem and then click Next.

Step 8:
Follow the modem wizard to the end.

Step 9:
Click OK on the Phone and Modem Options dialog. Your modem should
now be successfully installed.

=====================================================================
6.3.1 INSTALL SONY ERICSSON MOBILE PHONES IrDA MODEM FOR WINDOWS 2000
=====================================================================
You need Windows 2000 Service Pack 3 or later.

The automatic installation of the infrared (IR) modem starts when you
place your Sony Ericsson Mobile Phone, with the infrared port enabled,
in front of your PC's infrared eye. Windows will find your device and
install the modem automatically.

===================================================================================
6.3.2 INSTALL SONY ERICSSON MOBILE PHONES IrDA MODEM FOR WINDOWS XP SERVICE PACK 1A
===================================================================================
The automatic installation of the infrared (IR) modem starts when you
place your Sony Ericsson Mobile phone, with the infrared port enabled,
in front of your PC's infrared eye.

==================================================================================
6.3.3 INSTALL SONY ERICSSON MOBILE PHONES IrDA MODEM FOR WINDOWS XP SERVICE PACK 2
==================================================================================
A known issue on Windows XP service pack 2 is that the system wants to
install a "Standard modem over IR" instead of the correct IR modem.
However, it is the correct Sony Ericsson IrDA modem that is installed.

Step 1:
Start the Installation of the Sony Ericsson IrDA modem by following
Windows "Found new Hardware wizard".

Step 2:
The first step of the wizard asks you to install software for "Standard Modem over IR link".
Select the option "Install the software automatically".

Step 3:
The correct Sony Ericsson IrDA modem is installed automatically.
Your modem should now be successfully installed.

=====================================================================
7. LIMITATIONS
=====================================================================
Synchronisation

If there is more data in the PIM than allowed in the phone, the
synchronisation will complete successfully, but some items are not
synchronised to the phone. It is a good rule to check the
number of items in the phone from time to time to make sure that
there is enough space for new items to be synchronised.

Under "Sync Manager -> Settings -> Conflict policy" there
is an option "Use the item last modified". This option is only applicable
to data types Calendar and Tasks, for data types Contacts and Notes this
option will actually result in "Keep item in the PC and overwrite item
in the device", since these data types does not support a last changed date.

=====================================================================
8. KNOWN ISSUES February 10, 2006
=====================================================================
General

SYMPTOM: In some cases if using Mobile Networking Wizard and Bluetooth
the Sony Ericsson Bluetooth modem needs to be installed on the same com port
as the default Bluetooth Modem.
SOLUTION: Please follow instructions in 5.2 and 6.1 above.

SYMPTOM: Under certain conditions when trying to overinstall a newer
version over an older version of the PCSW problems may arise.
Problems finding the phone or running certain applications.
SOLUTION: Run a REPAIR installation from the CD or Web intallation.
It is also recommended to close ALL running applications and/or unistall
the older version of PCSW first. Please uninstall and reinstall the
phone cable drivers.

SYMPTOM: File Manager returns: "Unable to copy - an unexpected error has
occurred". Click "Try again". The message: "Unable to copy *** - the
operation has been aborted".
SOLUTION: The phone may not have enough free memory. There will be
memory full message on the phone. Free enough memory and download the
same file again.

SYMPTOM: Problem to download a MMS to the phone with the MMS Home Studio.
"Receiving item" pops up on the device but vanishes pretty quickly.
The MMS Home Studio returns "The file transfer was aborted".
Same problem might occur for Image Editor. In case of Image Editor
the error message is "Failed to transfer the image".
SOLUTION: The phone may not have enough free memory. There will be
memory full message on the phone. Free enough memory and download the
same file again.

SYMPTOM: File Manager does not display "Games" or "Applications" subfolders
SOLUTION: To add a .jar or "game" to the mobile.
1. Open File Manager
2. Connect mobile to PC via. Cable, Bluetooth or IrDA
3. In File Manager select "My " (depending on phone model connected)
4. Copy/Paste .jar or "game" over Phone Memory icon
RESULT: .jar or "game' can be saved in "Games" or "Applications" subfolder on mobile

Outlook users
SYMPTOM: Synchronisation is not possible after disconnecting the
computer from the network.
SOLUTION: Outlook must be restarted in "offline" mode.

SYMPTOM: Updates are not transferred correctly.
SOLUTION: Wait one minute and initiate another synchronisation.

SYMPTOM: When an item has been changed in both PIM and phone in a short
period of time and the slightly older version take precedence.
SOLUTION: Repeat the change and initiate another synchronisation.